STORM OFFICIAL GUIDE

Storm Drilling Layouts

Storm’s official drilling systems for symmetric and asymmetric balls: the Pin Buffer Layout System for one-handed bowlers and the 2LS (2-Hand Layout System) for two-handed and no-thumb bowlers, with the layouts Storm publishes for each.

By the BowlersMart Pro Shop Team. Sourced from Storm Products’ official drilling instructions. Last checked against Storm’s documents in October 2026.
IN THIS GUIDE
  • How to read a Storm layout
  • The 2LS arc system explained
  • 6 ranked 2LS layouts
  • 7 Pin Buffer layouts
  • Laying out a symmetric ball
  • Storm core specs
  • Official PDF downloads

Have a bowling question? Search the learning center.

OFFICIAL PDF

2LS Drilling Instructions

Download PDF ↓

OFFICIAL PDF

Pin Buffer Layout System

Download PDF ↓

OFFICIAL PDF

2LS Layouts Poster

Download PDF ↓

STORM’S SIGNATURE SYSTEM

The 2LS Layout System

Storm’s 2LS (2-Hand Layout System) is built for two-handed and no-thumb bowlers. With no thumb hole, it measures the PAP from the center of the bridge between the fingers instead of the center of the grip. A layout is drawn with five arcs, and the first three give the layout its three numbers.

The 5 Arcs That Define a 2LS Layout

ARC 1

Pin-to-PAP Arc

Controls how much flare the core uses. Longer than 3⅜” gives a later, more angular breakpoint. Shorter gives an earlier, smoother one.

ARC 2

PSA-to-PAP Arc

Controls post-drilled asymmetry and intermediate differential. On a symmetric ball, measure it from a point 6¾” from the pin through the CG.

ARC 3

Pin to Center of Grip Arc

Controls post-drilled total differential. Longer than 3⅜” makes the ball stronger overall. Shorter makes it weaker.

ARC 4

Lightning Arc

Drawn from the PAP across the pin-to-COG arc. Sets the minimum difference between the pin-to-PAP and pin-to-COG distances, from Storm’s Lightning Arc chart.

ARC 5

Vertical PAP Arc

Orients the PAP with the center of grip and sets where the midline runs.

Drilling tips from Storm: drill both fingers directly off the midline with no offset; even a slight offset changes the PAP and the layout dramatically. Storm does not recommend finger holes deeper than 2¾”. Past that the layout’s benefits taper off, and deeper holes raise the RG, which in most cases means a later ball with less overall motion.
REFERENCE LAYOUTS

2LS Layouts: Weakest to Strongest

Storm’s official 2LS ladder. Each layout is written as three measurements in this order: Pin-to-PAP, PSA-to-PAP, then Pin-to-COG (pin to the center of grip). Storm’s examples all use a PAP 5″ over and 1″ down from the center of the bridge.

RANK 1 • WEAKEST
5½” x 5″ x 2″
PIN→PAP
5½”
PSA→PAP
5″
PIN→COG
2″
Reaction: Very low flare. Straight through the front and clean through the midlane, then more responsive downlane when there is friction.
Best for: Burned lanes and older lane surfaces. It can miss the spot when the lanes play tight.
RANK 2 • LOW FLARE
2″ x 6″ x 5″
PIN→PAP
2″
PSA→PAP
6″
PIN→COG
5″
Reaction: Low flare, controllable, stable and smooth.
Best for: Short patterns with backend friction. Rev dominant players.
RANK 3 • THE BENCHMARK
5″ x 4″ x 3½” (Start Here)
PIN→PAP
5″
PSA→PAP
4″
PIN→COG
3½”
Reaction: The blend of power and control Storm calls ideal, and a good read on the pattern.
Best for: Every player as a starting point. Storm calls it the benchmark; how well it suits a given pattern depends on the bowler’s style.
RANK 4 • SPEED DOMINANT
4½” x 3″ x 4½”
PIN→PAP
4½”
PSA→PAP
3″
PIN→COG
4½”
Reaction: More midlane, slightly less exit angle. More forward direction in the roll phase.
Best for: Speed dominant players on medium-long patterns with higher oil volumes.
RANK 5 • TRANSITION
4″ x 4″ x 5″
PIN→PAP
4″
PSA→PAP
4″
PIN→COG
5″
Reaction: Strong, capable, confidence inspiring. Excellent on urethane covers.
Best for: Lanes that are starting to transition. Blends out over/under conditions.
RANK 6 • STRONGEST
3½” x 4″ x 6½”
PIN→PAP
3½”
PSA→PAP
4″
PIN→COG
6½”
Reaction: Highly aggressive, earliest forward roll, most forward direction.
Best for: Fresh, high-volume patterns and extremely speed dominant bowlers. Not recommended on high friction surfaces or lower volume patterns.
STORM’S WORKED EXAMPLE
5″ x 4″ x 4″
PIN→PAP
5″
PSA→PAP
4″
PIN→COG
4″
What it is: The layout Storm draws step by step in its 2LS drilling instructions (download above), for a two-handed or no-thumb bowler with a PAP 5″ over and 1″ down from the center of the bridge.
Use it for: Following Storm’s instructions before you lay out your own numbers.
ONE-HANDED BOWLERS

Storm’s Pin Buffer Layouts

For one-handed bowlers, Storm writes a layout as three measurements in this order: Pin-to-PAP, PSA-to-PAP, then the pin buffer, the distance from the pin to the bowler’s vertical axis line (VAL). These are the seven layouts in Storm’s current Pin Buffer Layout System, with Storm’s own label on each. Each one is a starting point in our Layout Studio, which draws it on your ball and writes it in Dual Angle.

PIN-TO-PAP

Controls flare

0 to 2″: less flare and a smoother shape. 3 to 4″: more flare, earlier and stronger. 5 to 6″: less flare again, cleaner and more responsive.

PSA-TO-PAP

Controls stability

0 to 2″: a stable core, smoother transition and less overall motion. 3 to 4″: less stable, more flare and a faster, stronger response. 5 to 6″: stable again, less flare and more length.

PIN BUFFER

Controls transition

0 to 2″: a quicker, more aggressive response to friction. 2 to 3″: balanced and readable. 3 to 5″: slower and smoother, more controlled.

CONTROL • EARLY, SMOOTH
2″ x 6″ x 1″
PIN→PAP
2″
PSA→PAP
6″
PIN BUFFER
1″
A control layout for flat, difficult patterns. Very smooth off the end of the pattern and predictable for every style.
WEAK • LATE, SMOOTH
6″ x 5″ x 3″
PIN→PAP
6″
PSA→PAP
5″
PIN BUFFER
3″
Storm’s weakest layout: the least flare and the most length. For burned lanes or very high friction when you need control and length.
CONTROL BENCHMARK • MIDLANE, SMOOTH
5″ x 5″ x 4″
PIN→PAP
5″
PSA→PAP
5″
PIN BUFFER
4″
Clean through the front with a smoother motion downlane. For higher friction surfaces or when you want a controlled shape.
STRONG BENCHMARK • EARLY, ARC
4½” x 3″ x 2″
PIN→PAP
4½”
PSA→PAP
3″
PIN BUFFER
2″
An earlier midlane roll with more forward motion downlane. Good for speed dominant players who need a stronger read.
UNIVERSAL BENCHMARK • MIDLANE, BALANCED
5″ x 4″ x 2″ (Start Here)
PIN→PAP
5″
PSA→PAP
4″
PIN BUFFER
2″
A balanced, predictable shape on almost any condition. Storm’s starting point for a versatile arsenal.
STRONG CONTROL • EARLY, ROUND
4″ x 4″ x 1″
PIN→PAP
4″
PSA→PAP
4″
PIN BUFFER
1″
Strong midlane stability with a controlled backend. For medium to heavy oil when you want a smoother, earlier roll.
STRONG • EARLY, STRONG
3″ x 4½” x 2″
PIN→PAP
3″
PSA→PAP
4½”
PIN BUFFER
2″
Very strong overall with high flare potential. For rev dominant players who need an earlier roll and more total hook.
Storm’s warranty rule: if the pin would land within 1″ of a hole, move the center of grip so the pin is drilled out completely or sits more than 1″ from the hole. Drilling partly into the pin voids the warranty. Storm’s drawings are for right-handed bowlers, so mirror them for a left-hander. Storm’s Pin Buffer drilling sheet (download above) walks through a 4″ x 4″ x 2″ step by step.
SYMMETRIC CORE

Laying Out a Symmetric Storm Ball

A symmetric ball has a pin but no engraved PSA. Storm’s symmetric drill sheet starts by marking a stand-in: the point 6¾” from the pin, measured through the center of gravity (CG). Measure PSA-to-PAP from that mark and lay the ball out with the same three numbers. Storm notes this is the undrilled PSA, which moves once the holes are drilled. The 2LS uses the same 6¾” point on a symmetric ball.

FROM STORM’S SYMMETRIC DRILL SHEET
4″ x 4″ x 2″
PIN→PAP
4″
PSA→PAP
4″
PIN BUFFER
2″
High flaring and strong. Works on many patterns with a strong entry angle.
FROM STORM’S SYMMETRIC DRILL SHEET
5″ x 4″ x 3″
PIN→PAP
5″
PSA→PAP
4″
PIN BUFFER
3″
Length with backend. Suits drier fronts or a deep inside line, with a late breakpoint.
FROM STORM’S SYMMETRIC DRILL SHEET
3½” x 5″ x 3″
PIN→PAP
3½”
PSA→PAP
5″
PIN BUFFER
3″
Very strong and made for long patterns. Storm does not recommend it for crankers or very high track bowlers.
FROM STORM’S SYMMETRIC DRILL SHEET
5″ x 3″ x 4″
PIN→PAP
5″
PSA→PAP
3″
PIN BUFFER
4″
Good length and a late midlane. A control layout for low volume or wet/dry lanes.

Storm draws each of these for two bowlers: a low track PAP of 3½” over by ¾” up and a high track PAP of 5″ over by ¼” up. The same numbers land the holes in different places on each, which is why a layout starts from your measured PAP.

Storm Core Specs

A layout works with the core inside the ball. Our Storm core library shows each Storm core’s RG and differential and whether it is symmetric or asymmetric, so you know which section above applies before the ball is laid out.

Storm Drilling FAQ

Common questions about applying these layouts to your Storm ball.

2LS is Storm’s 2-Hand Layout System. It was built for two-handed and no-thumb bowlers: traditional layout math measures the PAP from the center of the grip between the thumb and finger holes, and a no-thumb ball has no thumb hole. The 2LS measures the PAP from the center of the bridge between the fingers instead. Storm’s examples use a PAP 5 inches over and 1 inch down from there.
The Rank 3 benchmark layout: Pin-to-PAP 5″, PSA-to-PAP 4″, Pin-to-COG 3½”. Storm calls it the benchmark, a starting point for every player to get a read on the pattern. From there, pick by the job Storm gives each layout: rank 1 for burned lanes and older surfaces, rank 2 for short patterns with friction at the end, rank 4 for speed dominant players on medium-long, higher-volume patterns, rank 5 for lanes that are starting to transition, and rank 6 for fresh, high-volume patterns. One-handed bowlers with a thumb start from the Pin Buffer layouts instead, where Storm’s universal benchmark is 5″ x 4″ x 2″.
Asymmetric Storm balls have an engraved PSA (Preferred Spin Axis) marker, a small lightning bolt, in addition to the pin and the CG mark. Symmetric balls have a pin and a CG mark but no PSA marker. Our Storm core library lists each Storm core as symmetric or asymmetric. On a symmetric ball, mark the PSA reference point 6¾” from the pin through the CG, as shown in the symmetric section above.
Lightning Strike was the name on Storm’s earlier PSA Layout Guide for asymmetric balls. It laid a ball out with three measurements: pin-to-PAP, PSA-to-PAP and the pin buffer, the distance from the pin to the bowler’s vertical axis line (VAL), with a 4″ x 4″ x 2″ as its step-by-step example. Storm’s current Pin Buffer Layout System uses the same three measurements, so start with the Pin Buffer layouts above.
Storm says the layout’s benefits begin to taper off past 2¾”. As the finger holes get deeper, the ball’s RG goes up wherever the holes are, which in most cases means a later ball with less overall motion. Finger depth is part of the layout: Storm says to set it by the reaction you want and the pin-to-COG distance you chose.
The way a 2LS layout is measured and drawn works on any ball, but Storm’s reaction notes describe what those layouts do on Storm balls. Cores differ from ball to ball, so the same numbers on a different ball will not necessarily give the same reaction. For other brands, start from that manufacturer’s published layouts and use the 2LS as a way to think about the layout, not a recipe.

More From the Drilling Hub

HUB

All Drilling Layouts

The complete reference: Dual Angle, VLS, 2LS, the 8 most common layouts, and brand guides.

View the hub →

ANOTHER BRAND

Brunswick Drilling Layouts

Brunswick’s official symmetric and asymmetric drilling instructions plus full-roller variants.

View Brunswick guide →

ANOTHER BRAND

Motiv Drilling Layouts

Motiv’s recommended layouts across their performance ball lineup.

View Motiv guide →

NEXT STEP

Have a Storm layout in mind? Take it to a pro shop.

These layouts give a certified Storm driller the starting geometry. Your measured PAP, span, pitches, and rev rate decide the final numbers. Find a BowlersMart pro shop near you to book a fitting.